How To Change Honda Crv Brake Light

Honda CR-5 Tail Calorie-free Bulbs Replacement Guide
How to modify a burnt out restriction, turn signal, reverse or parking light seedling in a 3rd generation 2007-2011 Honda CR-5.

2011 CR-Five Tail Low-cal
Open Cargo Tail Gate Door
Pry Out Screw Cover This automotive maintenance tutorial was specifically written to help owners of the third generation (2007, 2008, 2009, 2010 & 2011) Honda CR-V in irresolute a burnt out brake, rear plow signal, reverse or parking bulb in the tail light housings.

Owners of other Honda or Acura SUV, minivan or hatchback vehicles such as the Pilot, Insight, CR-Z, Fit, Crosstour, Odyssey, TSX Sport Carriage, RDX and MDX may likewise find these DIY instructions to be helpful.

Replacement bulbs with their part numbers are equally follows: Brake # 7443, Turn Signal # WY21W (likewise 7440A or 7440NA), Reverse Light # 7440 and Parking Light (Rear Side Marker) # 2825 (or 168 or W5W).

Please verify the correct replacement part numbers for your SUV by using the Amazon Role Finder website. The compatible light bulb may vary depending on the model twelvemonth, trim level and whether it is a Northward American or European model.

Update - The possessor of a 2007 CR-V sold in Canada has informed me that the 7440A bulbs do non fit into their rear turn point bulb sockets. The seedling socket may just take the European specification WY21W light bulbs.

The only tools needed to replace any of the tail light bulbs is a standard Phillips head screwdriver and a small plastic automotive pry bar tool or a pocket-size flathead screwdriver.

Upper Phillips Head Spiral
Pry Out Lower Cover
Lower Cover Removed The start two steps are to open the tail gate door and move to the side of the vehicle with the burnt out bulb.

So gently pry out the two modest plastic spiral covers on the inner border of the tail light housing with a small flathead screwdriver.

Set up the two screw covers aside in a condom identify.

Remove Upper Screw
Phillips Spiral Removed
Loosen Counter Clockwise Remove the ii screws by turning them counterclockwise with the Phillips head screwdriver.

Set the 2 screws bated with the plastic covers.

2 Covers & 2 Screws
Loosen Friction Fasteners
Pry Off Tail Light Housing The housing is also held in place by three plastic pop rivet friction fasteners on the back side near the outer edge.

Carefully pull the tail light assembly straight off the rear corner of the vehicle.

If you have trouble removing the housing, effort gently wiggling it while pulling.

If necessary, use a plastic automotive panel pry tool or a pocket-sized flathead screwdriver covered with a sparse micro fiber fabric to gently loosen the pop rivets past prying off the outer border.

Towel On Bumper
Rear of Tail Lite Housing
Parking Light At Top Place a towel on the bumper to protect the plastic tail light lens and the painted bumper from being scratched.

The Parking Lite (A.K.A. rear side mark) is located at the top of the housing.

ane/iv Turn Counterclockwise
Pull Out Quondam # W5W Bulb
Push In New # W5W Seedling Rotate the parking light bulb socket ane/4 turn counterclockwise and pull information technology directly out of the housing.

Pull the erstwhile bulb direct out of the socket and push in a new # 2825 bulb.

You may too use whatsoever other miniature wedge base light bulbs such equally the # 168, 194, W5W or a compatible LED unit of measurement.

Re-insert the socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.

Brake Light Bulb Socket
1/4 Turn Counterclockwise
Remove Bulb Socket The Brake low-cal bulb socket is located but below the parking light and above the plough signal closer to the center of the assembly.

Rotate the socket 1/4 turn counterclockwise and pull information technology directly out of the housing.

Pull the old seedling direct out of the socket and button in a new # 7443 bulb.

(You lot may as well use the European specification # W21/5W seedling.)

Pull Out Former 7443 Bulb
1/4 Turn Clockwise - Lock
Plough Signal Bulb Socket Re-insert the restriction light seedling socket in to the housing and rotate it 1/4 turn clockwise to secure it in identify.

The Turn Signal light bulb socket is located just below the brake light and to a higher place the opposite lite.

1/4 Turn Counterclockwise
Pull Out Old # WY21W Bulb
1/four Turn Clockwise - Lock Rotate the plow indicate seedling socket 1/4 turn counterclockwise and pull it straight out of the housing.

Pull the onetime bulb straight out of the socket and push in a new amber colored # WY21W seedling.

(You may too be able to use the # 7440A or 7440NA bulbs.)

Re-insert the bulb socket in to the housing and rotate information technology 1/iv plough clockwise to secure information technology in place.

Opposite Bulb Socket
Pull Out Onetime # 7440 Bulb
Replace i/4 Turn Clockwise The Contrary or "back up" light seedling socket is located at the bottom of the housing.

Rotate the socket ane/iv turn counterclockwise and pull it directly out of the assembly.

Pull the old seedling directly out of the socket and push in a new # W21W or 7440 bulb.

Re-insert the socket in to the assembly and rotate information technology ane/4 plough clockwise to secure it in place.

Line Up Pegs & Holes
White Plastic Popular Rivet
Push On Tail Calorie-free Housing Line up the 3 white plastic popular rivet friction fasteners on the rear of the tail light housing with their corresponding holes in the metallic body panel.

Button the tail low-cal assembly back in to place on the corner of the vehicle.

Tighten Upper Screw
Plow Phillips Clockwise
Line Up Plastic Comprehend Tighten the two screws on the inner border of the housing by turning them clockwise with the Phillips caput screwdriver.
Popular In Screw Comprehend
Supplant Lower Encompass
Test New Tail Light Bulbs Push the two plastic screw covers back in to place.

Test the new tail light bulbs by having someone plough on the parking lights, step on the brake pedal, activate the chance signals and place the manual in opposite.

For more than, cheque out my other Honda CR-V Repair & Maintenance Guides.

Source: https://www.paulstravelpictures.com/Honda-CR-V-Tail-Light-Bulbs-Replacement-Guide/

Posted by: bynumraimad.blogspot.com

Share this post